| Model |
C9124AXE-ROW |
| Software |
● Cisco IOS XE Software Release 17.6.2 or later |
| Supported WLAN controllers |
● Cisco Catalyst 9800 Series Wireless Controllers |
| 802.11n version 2.0 (and related) capabilities |
● 4x4:4 in 2.4GHz + two 2x2:2 radios in 5 GHz uplink/downlink MU-MIMO |
| ● Maximal Ratio Combining (MRC) |
| ● 802.11n and 802.11a/g |
| ● 20- and 40-MHz channels |
| ● PHY data rates up to 890 Mbps (40 MHz with 5 GHz and 20 MHz with 2.4 GHz) |
| ● Packet aggregation: Aggregate MAC Protocol Data Unit (A-MPDU) (transmit and receive), Aggregate MAC Service Data Unit (A-MSDU) (transmit and receive) |
| ● 802.11 Dynamic Frequency Selection (DFS) |
| ● Cyclic Shift Diversity (CSD) support |
| 802.11ac |
● 4x4:4 in 2.4GHz + two 2x2:2 radios in 5 GHz uplink/downlink MU-MIMO |
| ● MRC |
| ● 802.11ac beamforming |
| ● 20-, 40-, 80- and 80+80-MHz channels |
| ● PHY data rates up to 3.47 Gbps (160 MHz with 5 GHz) |
| ● Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive) |
| ● 802.11 DFS |
| ● CSD support |
| ● WPA3 support |
| 802.11ax |
● 4x4:4 in 2.4GHz + two 2x2:2 radios in 5 GHz uplink/downlink MU-MIMO Uplink/downlink OFDMA |
| ● TWT |
| ● BSS coloring |
| ● MRC |
| ● 802.11ax beamforming |
| ● 20-, 40-, 80-, and 80+80-MHz channels |
| ● PHY data rates up to 5.38 Gbps (160 MHz with 5 GHz and 20 MHz with 2.4 GHz) |
| ● Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive) |
| ● 802.11 DFS |
| ● CSD support |
| ● WPA3 support |
| ● WPA3-Enterprise 192 support |
| External antenna |
● The Catalyst 9124AXE Access Point is certified for use with antenna gains up to 13 dBi (2.4 GHz and 5GHz) |
| ● Cisco offers the industry's broadest selection of antennas, delivering optimal coverage for a variety of deployment scenarios. |
| ● Supports Self-Identifiable Antennas (SIA) |
| Interfaces |
● 1x 100/1000/2500 BASE-T (Ethernet) uplink interface |
| ● 1x Gigabit Ethernet SFP |
| ● Supports PoE output (802.3af compliant PSE) on the 1x 10/100/1000 BASE-T (Ethernet) downlink interface if C9124AX powered from one of the following: |
| ◦ UPOE or 802.3bt inline power source (Switch or Power Injector) |
| ◦ DC input (with external power supply rated ≥ 60W) |
| ● Management console port (RJ-45) |
| Indicators |
● Status LED indicates boot loader status, association status, operating status, boot loader warnings |
| Dimensions (W x L x H) |
● Access point (without mounting brackets): 10.2 x 9.2 x 3.2 in. (25.9 x 23.3 x 8.1 cm) |
| Weight |
● 7 lb. (3.1 kg) |
| Input power requirements |
● 802.3af Power over Ethernet (PoE), 802.3at PoE+, 802.3bt PoE++, Cisco Universal PoE (Cisco UPOE) |
| ● Cisco power injector, AIR-PWRINJ-60RGD1= and AIR-PWRINJ-60RGD2= |
| ● Cisco power injector, AIR-PWRINJ6= (Note: This injector supports 802.3at) |
| ● DC power source: Auxiliary DC input, 24V to 56V |
| Environmental |
● Nonoperating (storage) temperature: -40° to 185°F (-40° to 85°C) |
| ● Nonoperating altitude test: 17,000 ft (5182 m) |
| ● Operating temperature: -40° to 149°F (-40° to 65°C) with no solar loading, -40° to 131°F (-40° to 55°C) with solar loading |
| ● Operating altitude test: 17,000 ft (5182 m) |
| ● Operating humidity: 0% to 100% (condensing) |
| ● IEC 60529 Ingress Rating: IP66/IP67 |
| ● Wind resistance up to 100 mph (161 km/h) sustained winds and 165 mph (266 km/h) wind gusts |
| ● Icing protection: MIL-STD-810F,13mm 13mm (0.5 in.) |
| ● Corrosion: NEMA 250-2008 (600 hrs. salt, 1200 hrs. mixed gas) |
| ● Solar radiation: EN 60068-2-5 (1120 W/m2) |
| ● Vibration: MIL-STD-810E, Method 514.4 (0.41 Grms from 3Hz to 500Hz, 2 hours per each axis X,Y,Z) |
| Available Tx power settings (max/min) |
2.4 GHz |
5 GHz |
| ● 30 dBm (1W) |
● 30 dBm (1W) |
| ● -4 dBm (0.4 mW) |
● -4 dBm (0.4 mW) |
C9124AXE-ROW mang lại lợi ích gì khi hỗ trợ anten ngoài Self-Identifiable Antennas (SIA)?
C9124AXE-ROW hỗ trợ Self-Identifiable Antennas (SIA), cho phép Access Point tự động nhận diện loại anten Cisco được kết nối và áp dụng cấu hình RF phù hợp. Điều này giúp tối ưu vùng phủ sóng, giảm sai sót trong quá trình triển khai và đảm bảo hiệu suất không dây ổn định ở nhiều môi trường khác nhau.
Vì sao C9124AXE-ROW phù hợp với các khu vực ngoài trời có mật độ người dùng cao?
C9124AXE-ROW sử dụng kiến trúc 4x4:4 trên băng tần 2.4 GHz kết hợp hai radio 5 GHz 2x2:2, hỗ trợ MU-MIMO, OFDMA, Beamforming và tốc độ PHY lên đến 5.38 Gbps. Kiến trúc này giúp tăng dung lượng phục vụ, giảm tắc nghẽn và cải thiện hiệu quả truyền dữ liệu khi có nhiều thiết bị truy cập đồng thời.
C9124AXE-ROW có những đặc điểm nào giúp giảm chi phí và tăng tính linh hoạt khi triển khai?
C9124AXE-ROW hỗ trợ nhiều phương thức cấp nguồn như PoE, PoE+, PoE++, Cisco UPOE và nguồn DC, đồng thời tích hợp cổng Ethernet 2.5GbE, cổng Gigabit SFP và cổng Ethernet downlink hỗ trợ PoE output khi được cấp nguồn đủ công suất. Nhờ đó, thiết bị có thể cấp nguồn cho các thiết bị phụ trợ như camera IP hoặc cảm biến, giúp đơn giản hóa hạ tầng và giảm chi phí lắp đặt.