| Model |
C9124AXI-ROW |
| Software |
● Cisco IOS XE Software Release 17.5.1/17.3.4 (B Domain) or later |
| ● Cisco IOS XE Software Release 17.6.2 or later (For all Regulatory Domains) |
| Supported WLAN controllers |
● Cisco Catalyst 9800 Series Wireless Controllers |
| 802.11n version 2.0 (and related) capabilities |
● 4x4:4 in both 2.4GHz and 5 GHz uplink/downlink MU-MIMO with four spatial streams |
| ● Maximal Ratio Combining (MRC) |
| ● 802.11n and 802.11a/g |
| ● 20- and 40-MHz channels |
| ● PHY data rates up to 890 Mbps (40 MHz with 5 GHz and 20 MHz with 2.4 GHz) |
| ● Packet aggregation: Aggregate MAC Protocol Data Unit (A-MPDU) (transmit and receive), Aggregate MAC Service Data Unit (A-MSDU) (transmit and receive) |
| ● 802.11 Dynamic Frequency Selection (DFS) |
| ● Cyclic Shift Diversity (CSD) support |
| 802.11ac |
● 4x4:4 in both 2.4GHz and 5 GHz uplink/downlink MU-MIMO with four spatial streams |
| ● MRC |
| ● 802.11ac beamforming |
| ● 20-, 40-, 80- and 80+80-MHz channels |
| ● PHY data rates up to 3.47 Gbps (160 MHz with 5 GHz) |
| ● Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive) |
| ● 802.11 DFS |
| ● CSD support |
| ● WPA3 support |
| 802.11ax |
● 4x4:4 in both 2.4GHz and 5 GHz uplink/downlink MU-MIMO with four spatial streams |
| ● TWT |
| ● BSS coloring |
| ● MRC |
| ● 802.11ax beamforming |
| ● 20-, 40-, 80-, and 80+80-MHz channels |
| ● PHY data rates up to 5.38 Gbps (160 MHz with 5 GHz and 20 MHz with 2.4 GHz) |
| ● Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive) |
| ● 802.11 DFS |
| ● CSD support |
| ● WPA3 support |
| ● WPA3-Enterprise 192 support |
| Integrated antenna |
● 2.4 GHz: Peak gain 7 dBi, internal antenna, Vertical Polarization, omnidirectional |
| ● 5 GHz: Peak gain 7 dBi, internal antenna, Vertical Polarization, omnidirectional |
| ● BLE Antenna Gain: 5 dBi, internal antenna, Vertical Polarization, omnidirectional |
| Interfaces |
● 1x 100/1000/2500 BASE-T (Ethernet) uplink interface |
| ● 1x Gigabit Ethernet SFP |
| ● Supports PoE output (802.3af compliant PSE) on the 1x 10/100/1000 BASE-T (Ethernet) downlink interface if C9124AX powered from one of the following: |
| ◦ UPOE or 802.3bt inline power source (Switch or Power Injector) |
| ◦ DC input (with external power supply rated ≥ 60W) |
| ● Management console port (RJ-45) |
| Indicators |
● Status LED indicates boot loader status, association status, operating status, boot loader warnings |
| Dimensions (W x L x H) |
● Access point (without mounting brackets): 10.2 x 9.2 x 3.2 in. (25.9 x 23.3 x 8.1 cm) |
| Weight |
● 6.5 lb. (2.9 kg) |
| Input power requirements |
● 802.3af Power over Ethernet (PoE), 802.3at PoE+, 802.3bt PoE++, Cisco Universal PoE (Cisco UPOE) |
| ● Cisco power injector, AIR-PWRINJ-60RGD1= and AIR-PWRINJ-60RGD2= |
| ● Cisco power injector, AIR-PWRINJ6= (Note: This injector supports 802.3at) |
| ● DC power source: Auxiliary DC input, 24V to 56V |
| Environmental |
● Nonoperating (storage) temperature: -40° to 185°F (-40° to 85°C) |
| ● Nonoperating altitude test: 17,000 ft (5182 m) |
| ● Operating temperature: -40° to 149°F (-40° to 65°C) with no solar loading, -40° to 131°F (-40° to 55°C) with solar loading |
| ● Operating altitude test: 17,000 ft (5182 m) |
| ● Operating humidity: 0% to 100% (condensing) |
| ● IEC 60529 Ingress Rating: IP66/IP67 |
| ● Wind resistance up to 100 mph (161 km/h) sustained winds and 165 mph (266 km/h) wind gusts |
| ● Icing protection: MIL-STD-810F,13mm 13mm (0.5 in.) |
| ● Corrosion: NEMA 250-2008 (600 hrs. salt, 1200 hrs. mixed gas) |
| ● Solar radiation: EN 60068-2-5 (1120 W/m2) |
| ● Vibration: MIL-STD-810E, Method 514.4 (0.41 Grms from 3Hz to 500Hz, 2 hours per each axis X,Y,Z) |
| Available Tx power settings (max/min) |
2.4 GHz |
5 GHz |
| ● 30 dBm (1W) |
● 30 dBm (1W) |
| ● -4 dBm (0.4 mW) |
● -4 dBm (0.4 mW) |
Vì sao Cisco C9124AXI-ROW phù hợp cho các hệ thống mạng ngoài trời quy mô lớn?
Cisco C9124AXI-ROW được thiết kế với chuẩn bảo vệ IP66/IP67, hỗ trợ hoạt động trong dải nhiệt độ -40°C đến 65°C, chống bụi, nước, ăn mòn, rung động và gió mạnh theo các tiêu chuẩn công nghiệp. Bên cạnh đó, thiết bị hỗ trợ nhiều phương thức cấp nguồn như 802.3af PoE, PoE+, PoE++, Cisco UPOE và nguồn DC, giúp triển khai linh hoạt tại các khu vực ngoài trời yêu cầu độ bền và tính sẵn sàng cao.
Công nghệ Wi-Fi 6 trên Cisco C9124AXI-ROW giúp cải thiện hiệu suất mạng như thế nào?
C9124AXI-ROW sử dụng chuẩn Wi-Fi 6 (802.11ax) với 4×4 MU-MIMO, OFDMA, Target Wake Time (TWT) và BSS Coloring, cho phép phục vụ đồng thời nhiều thiết bị mà vẫn duy trì hiệu suất ổn định. Thiết bị đạt tốc độ PHY tối đa 5,38 Gbps, phù hợp cho các môi trường có mật độ người dùng cao như khu công nghiệp, sân vận động và khuôn viên trường học.
Điểm nổi bật của Cisco Catalyst C9124AXI-ROW về khả năng kết nối có dây là gì?
Cisco C9124AXI-ROW được trang bị cổng Ethernet Multigigabit 2.5GbE kết hợp với 1 cổng Gigabit SFP, đáp ứng nhu cầu truyền tải dữ liệu tốc độ cao của Wi-Fi 6. Thiết bị còn hỗ trợ PoE Out (802.3af PSE) để cấp nguồn cho các thiết bị IP như camera hoặc Access Point phụ, giúp giảm chi phí triển khai và tối ưu hạ tầng mạng ngoài trời.