| Model |
IW9167EH-ROW-URWB |
| Software |
● Cisco Unified Industrial Wireless Software 17.11.1 or later |
| Supported wireless LAN controllers |
● Cisco Catalyst 9800 Series Wireless Controllers (physical or virtual) |
| 802.11n version 2.0 (and related) capabilities |
● 4x4 MIMO with four spatial streams in one 2.4 GHz radio and two 5 GHz radios |
| ● Maximal Ratio Combining (MRC) |
| ● 802.11n and 802.11a/g |
| ● 20- and 40-MHz channels |
| ● PHY data rates up to 1.5 Gbps (with 40 MHz on both 5 GHz radios and 20 MHz on the 2.4 GHz radio) |
| ● Packet aggregation: Aggregate MAC Protocol Data Unit (A-MPDU) (transmit and receive), Aggregate MAC Service Data Unit (A-MSDU) (transmit and receive) |
| ● 802.11 Dynamic Frequency Selection (DFS) |
| ● Cyclic Shift Diversity (CSD) support |
| 802.11ac |
● 4x4 downlink MU-MIMO with four spatial streams on both 5 GHz radios |
| ● Maximal Ratio Combining (MRC) |
| ● 802.11ac beamforming |
| ● 20, 40, and 80 MHz channels |
| ● PHY data rates up to 3.4 Gbps (dual 4x4:4SS 80 MHz) |
| ● Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive) |
| ● 802.11 DFS |
| ● CSD support |
| ● Wi-Fi Protected Access (WPA) 3 support |
| 802.11ax |
● 4x4 uplink/downlink MU-MIMO with four spatial streams in 2.4, 5, and 6 GHz* |
| ● Uplink/downlink OFDMA |
| ● Target Wake Time (TWT) |
| ● BSS coloring |
| ● Maximal Ratio Combining (MRC) |
| ● 802.11ax beamforming |
| ● 20, 40, 80, and 160 MHz channels (IW9167E 5/6 GHz radio, IW9167I, IW9167E-STA and IW9167E-STA2 6 GHz radio) |
| ● 20, 40, 80 channels (5 GHz radio) |
| ● 20 MHz channels (2.4 GHz radio) |
| ● PHY data rates up to 7.8 Gbps (4x4 160 MHz on 6 GHz, 4x4 80 MHz on 5 GHz, and 4x4 20 MHz on 2.4 GHz) |
| ● Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive) |
| ● 802.11 DFS |
| ● CSD support |
| ● WPA3 support |
| Antennas |
● 8x N-type antenna ports |
| ● 1x TNC GNSS antenna port |
| ● Cisco offers the industry's broadest selection of antennas, delivering optimal coverage for a variety of deployment scenarios. |
| ● Supports Self-Identifiable Antennas (SIA) |
| Interfaces |
● 1x 100M/1000M/2.5G/5G Multigigabit Ethernet (RJ-45)/M12 X-code autosensing PoE+ in (802.3at/bt), UPOE in |
| ● 1x SFP (copper) 100M/1000M/10G Multigigabit Ethernet /M12 X-code OR 1x SFP (fiber) 1G/10G |
| ● Management console port (RJ-45) |
| ● Multicolor system LED |
| ● DC power input (micro-fit/M12 A-code) |
| ● Reset button |
| Note: PG 13.5 glands or M12 adapters shall be used with Ethernet and power interfaces to meet IP67 rating. |
| Note: Catalyst IW9167E-HZ has permanent M25 ports. M12 adapters are not compatible. See Installation Guide for gland requirements. |
| Dimensions (W x L x H) |
● 11.5 x 10.5 x 2.8 in (29.2 x 26.7 x 7.1 cm) |
| Weight |
● 9.2 lb. (4.2 kg) |
| Input power requirements |
● 802.3at (PoE+), 802.3bt (PoE++), Cisco Universal PoE (Cisco UPOE®) |
| ● DC power source: 24 to 48 VDC (maximum voltage range: 18 to 60 VDC) |
| ● Cisco power AC-DC power adapter, IW-PWRADPT-MFIT4P= |
| ● Cisco power injector, IW-PWRINJ-60RGDMG= |
| Surge |
● DC power input |
| ◦ EN50121-4, ± 2 kV (line-earth) and ± 1 kV (line-line) |
| ◦ AREMA, ± 1 kV (line-earth) and ± 1 kV (line-line) |
| ◦ CISPR35, ± 0.5 kV (line-earth) |
| ● Surge protection to ± 2 kV on Ethernet ports |
| ● Surge protection to ± 1 kV on SFP copper port with shielded cable |
| Environmental |
● Nonoperating (storage) temperature: -40° to +185°F (-40° to +85°C) |
| ● Nonoperating (storage) altitude test: +25˚C (77˚F), 17,000 ft. |
| ● Operating temperature: -40° to +158°F (-40° to +70°C) with solar load and still air. |
| ● Extended operating temperature (DC powered, not applicable to IW9167ESTA and IW9167E STA2): -58° to +167°F (-50° to +75°C) without solar loading, still air, and cold start limited to-40°C |
| ● Operating type test: +85°C for 16 hours |
| ● Operating humidity: 0% to 100% (condensing) |
| ● Operating altitude: 15,000 ft. (4,500 m) |
| ● Wind resistance: Up to 160 mph (257 km/h) sustained winds |
| Environmental ratings |
● EN/IEC 60529 (IP66 and IP67) |
| System memory |
● 2048 MB DRAM |
| ● 1024 MB flash |
| Available conducted transmit power settings (max/min), all antennas active |
2.4 GHz |
5 GHz |
5/6 GHz |
| ● 24 dBm (250 mW) |
● 30 dBm (1 W) |
● 23 dBm (200 mW) |
| ● -4 dBm (0.4 mW) |
● -4 dBm (0.4 mW) |
● -4 dBm (0.4 mW) |
Cisco Catalyst IW9167EH-ROW-URWB khác gì so với Cisco Catalyst IW9167EH-ROW-AP?
Cisco Catalyst IW9167EH-ROW-URWB và IW9167EH-ROW-AP có cấu hình phần cứng gần như tương đương về giao diện mạng, khả năng kết nối và điều kiện hoạt động. Tuy nhiên, điểm khác biệt là IW9167EH-ROW-URWB được cài đặt Cisco Unified Industrial Wireless Software, hỗ trợ các ứng dụng URWB chuyên dụng cho môi trường công nghiệp, trong khi IW9167EH-ROW-AP sử dụng Cisco IOS XE và chủ yếu hoạt động như một Access Point Wi-Fi công nghiệp thông thường. Điều này giúp phiên bản URWB đáp ứng tốt hơn các yêu cầu về tính sẵn sàng và độ tin cậy trong các hệ thống công nghiệp quan trọng.
Cisco Catalyst IW9167EH-ROW-URWB phù hợp với những ứng dụng nào trong môi trường công nghiệp?
Cisco Catalyst IW9167EH-ROW-URWB được thiết kế cho các ứng dụng yêu cầu liên kết không dây có độ tin cậy cao (Ultra-Reliable Wireless Backhaul - URWB). Thiết bị phù hợp triển khai trong hệ thống tự động hóa nhà máy, phương tiện tự hành (AGV/AMR), khai thác mỏ, cảng biển và giao thông thông minh, nơi cần duy trì kết nối ổn định với độ trễ thấp và khả năng hoạt động liên tục.
Cisco Catalyst IW9167EH-ROW-URWB sử dụng Cisco Unified Industrial Wireless Software mang lại lợi ích gì?
Cisco Catalyst IW9167EH-ROW-URWB sử dụng Cisco Unified Industrial Wireless Software 17.11.1 hoặc mới hơn, được tối ưu cho các ứng dụng mạng công nghiệp. Nền tảng phần mềm này cho phép quản lý tập trung, hỗ trợ đồng thời các dịch vụ Wi-Fi doanh nghiệp và các ứng dụng truyền thông công nghiệp, giúp đơn giản hóa quá trình vận hành và nâng cao khả năng mở rộng của hệ thống.